247-5286 2475286 Machine Control Module ECM Controller for CAT 330C 330C L Excavator
247-5286 Machine Control Module for CAT 330C, 330C L and 330C LN excavators.
- Interchangeability: Cross-references 247-5286, 195-8915, 211-5551, 227-7605 and 195-8997.
- Application: For CAT 330C, 330C L, 330C LN, 330C FM and 330C MH excavators and the 330C mobile hydraulic power unit.
- Check Your Variant: This is the machine controller, not the engine ECM — match the number on your current module label first.
- Programmed Before Dispatch: Send your machine serial number (PIN) after checkout — we flash it to your machine before shipping.
$1,999.00
-
Bench-Tested - Every unit powered up and function-tested before dispatch.
-
6-Month Warranty - From delivery, against defects in materials and workmanship.
-
30-Day Returns - Unused items in original packaging. RMA required.
Product Details
▾
This remanufactured Machine Control Module, part number 247-5286 (also written 2475286), is an aftermarket replacement for Caterpillar 330C, 330C L, 330C LN, 330C FM and 330C MH excavators and the 330C mobile hydraulic power unit.
On the 330C the machine controller is the link between the operator, the hydraulics and the engine. It reads the speed dial, work mode switches and pressure sensors, sets main pump output against engine load, drives the hydraulic solenoids and passes the speed request on to the engine’s own control module. Each unit is opened, cleaned and inspected at circuit-board level. Components found worn or out of tolerance are replaced, the connector cavities are checked for moisture damage, and the finished controller is powered up and function-tested on the bench before it goes to programming.
- Reference numbers: 247-5286 / 2475286.
- Module type: Machine controller (Control GP-Machine). The 330C engine has its own separate engine module — check which one your fault points to.
- Fitment type: Direct replacement — same mounting position, same machine harness connectors.
- Application: For Caterpillar 330C, 330C L, 330C LN, 330C FM (forestry), 330C MH (material handler) and the 330C mobile hydraulic power unit.
- Programming: Configured to your machine by our technicians before the module leaves our facility — no flashing required after arrival.
- Packaging: Shipped in anti-static protection with impact-absorbing outer packing.
Send Us Your Machine Serial Number (PIN) — We Program The Module Before It Ships
A standard 330C L, a forestry 330C FM and a 330C MH material handler use the same controller hardware with different machine software. We load the software for your machine at our facility and send the controller ready to install — it is not shipped blank. The 1–3 business day dispatch window starts from the moment we receive your machine data — not from the order date — so please send the following right after checkout:
- Machine serial number (PIN) — in full, including the three-letter prefix, from the machine ID plate.
- Machine model and build — for example 330C L, 330C FM or 330C MH.
- Engine serial number — from the engine data plate, if it is readable.
- Clear photos of the label on your current controller and of the machine ID plate.
Installation note: Removal and installation should be carried out by an experienced technician. Lower the work tool to the ground, turn the battery disconnect switch off and wait for the electrical system to power down before unplugging the machine harness. Keep the connector faces clean and dry and tighten the connector fasteners to the machine service manual value.
Fitment & OEM Interchange
▾
OEM interchange numbers are listed as a cross-reference only, to help you identify the correct replacement. All brand names, model designations and part numbers belong to their respective owners and are used solely to describe compatibility.
| Reference Number | Format | Compatible Machine Families |
|---|---|---|
| 247-5286 | Primary number, with hyphen | For Caterpillar 330C series hydraulic excavators |
| 2475286 | Primary number, no hyphen | Same as above |
Application Chart — Fits for Caterpillar Excavators
| Machine Category | Compatible Models |
|---|---|
| Excavator | 330C, 330C L, 330C LN, 330C FM, 330C MH |
| Mobile Hydraulic Power Unit | 330C |
Confirm Before You Order
A 330C carries two main electronic modules: this machine controller and a separate engine control module on the engine. Make sure the fault is on the machine side, then compare the number printed on your current machine controller label with 247-5286. Not sure? Send us photos of the label and the machine ID plate and we will confirm fitment before you buy.
Technical Specifications
▾
| Specification | Detail |
|---|---|
| Part Name | Machine Control Module (Control GP-Machine) — Electronic Control Unit |
| Reference Numbers | 247-5286, 195-8915, 211-5551, 227-7605 and 195-8997 |
| Condition | Remanufactured |
| Installation Method | Direct replacement — fits the existing mounting position and machine harness connectors |
| Programming | Programmed before dispatch — no flashing required after arrival |
| System Voltage | Application dependent, confirm on data plate |
| Housing Material | Sealed metal housing |
| Connectors | Application dependent — confirm connector count and pin layout against your existing controller |
| Circuit Protection | Application dependent — refer to the machine electrical schematic |
| Testing | Bench-tested — powered up and function-tested before dispatch |
| Warranty | 6 months from delivery, against defects in materials and workmanship |
| Package Contents | 1 × Machine Control Module (harness, sensors and mounting hardware not included) |
Compliance statement: this controller is supplied to restore factory-specified performance only. It is programmed to the configuration recorded for your machine serial number and does not alter the certified machine or engine setup.
Common Failure Symptoms
▾
| Symptom | What It Usually Points To |
|---|---|
| Action alarm sounds at key-on and the monitor reports a machine controller error | Internal fault in the controller, or lost communication between the controller and the monitor. |
| Engine runs but stays at one speed however the speed dial is set | The controller is not reading the dial or not passing the speed request to the engine module; test the dial and its wiring first. |
| All functions are slow and the pumps never come up to full output | Pump control signal from the controller is missing or stuck at minimum. |
| Engine is dragged down hard whenever boom and swing are used together | Pump output is not being matched to engine load — the controller is misreading pressure or speed inputs. |
| Hydraulic lock stays engaged with the lockout lever in the unlocked position | Lockout input is not being read or the lock solenoid is not being driven; check the lever switch and solenoid first. |
| Service tool reaches the engine module but not the machine controller | Communication circuit in the machine controller has failed, or the data link to it is open. |
| Faults that started after water got into the cab | Moisture has reached the controller connectors; expect corrosion on the pins. |
| Hydraulics dead to all commands after a jump-start or welding on the machine | Over-voltage or welding current has damaged the controller’s input stage. |
Rule Out the Cheap Causes First
Before replacing the controller, check battery voltage with the key on, the controller fuses and the cab and frame grounds. Measure the speed dial, the lockout lever switch and the suspect solenoid coil directly, and inspect the machine harness under the cab and in the pump compartment for rubbed-through or oil-soaked wiring. Replace the controller only when power, ground, harness and components have been proven good.
Shipping & Quality Guarantee
▾
- Bench-Tested: Every unit is powered up and function-tested before dispatch.
- Dispatch: Dispatched in 1–3 business days, counted from the moment we receive your machine serial number (PIN) for programming.
- Delivery: Free express shipping by DHL / FedEx / UPS, 3–8 business days. Tracking number provided within 24–48 hours of dispatch.
- Packaging: Anti-static protection and impact-absorbing packing.
- 6-Month Warranty: Covers defects in materials and workmanship from the date of delivery. If a fault appears in this period, we repair or replace the unit.
- 30-Day Returns: Unused items in original packaging; an RMA number is required before sending anything back.
- Technical Support: Fitment checks before you order and installation guidance after delivery.
Shipping & Customs Notice
Our price covers the product and shipping only. Import duties, VAT, GST and any other local taxes or customs clearance fees are not included and are the buyer’s responsibility. Please check with your local customs office before ordering.
Caterpillar® and CAT® are trademarks of their respective owner and are used here only to describe compatibility. We are an independent aftermarket parts supplier and are not affiliated with, endorsed by or sponsored by any machine or engine manufacturer.

Reviews
Clear filtersThere are no reviews yet.